Embroidery hoop art: Personalized headband holder

Cute embroidery hoop headband holder tutorial by molly and mama for sewmccool.com

Let’s welcome Lauren again, of Molly and Mama! Lauren has made a beautiful embroidery hoop headband holder for her second tutorial in the Little Girl’s Bedroom Makeover series!

Take it away, Lauren!

My daughter has a really large hair clip holder on her wall that’s loaded with all the pretty clips I have bought and made her. But until now we’ve had nowhere to store her lovely head bands! So I decided to create this a simple headband holder tutorial using an embroidery hoop, some ribbon, fabric and felt. And I really love that it’s personalised.

You Will Need

* 8in timber embroidery hoop
* 10in  square of pretty floral fabric
* 10in square of fusible batting like Pellon (not sure what you guys call it)
* 8in wide piece of wool felt
* 8in wide piece of fusible webbing like Vliesofix or Easyfix
* 30in of 1.5in-wide grosgrain ribbon
* 36in of 1in-wide grosgrain ribbon
* More ribbon for a decorative bow
* Water erasable pen
* Hot glue gun
* Sewing machine and threads to coordinate with your fabric, felt and ribbon
* Scissors
* Iron and ironing board
* Press cloth or piece of soft cotton or lawn
* Computer and printer
* Ruler or measuring tape
* Heat sealer, lighter or matches

Edited M&M01

Headband holder tutorial

Using a word processing program, type out the name you wish to use for your project. Use a wide cursive font so that it’s easy to appliqué. I used the font ‘creampuff’. Make sure it’s about 7” long when printed so that it will fit nicely inside the embroidery hoop. When you go to print it, choose a printer setting that lets you print in reverse. My Canon printer says ‘flip horizontally’. That way your appliqué won’t be backwards!

Take your piece of fusible webbing and trace the name (with the paper side up) roughly around the text, leaving a small border. Do not cut out on your drawn line.

Lay your fusible webbing over your piece of wool felt. Heat your iron to a hot non-steam setting. Cover your webbing and felt with a press cloth. Fuse the paper to the felt by running the hot iron over it for a few seconds. Don’t attempt this step without the press cloth or the heat from the iron could damage the felt.

Take some small sharp scissors and carefully cut out the felt name. Pop it aside for a moment.

Headband holder collage 1

Now, centre your hoop on the back of your fabric square. Using your erasable marker pen, draw around the outside of the hoop.

Cut out a wider circle about an inch out from the circle you have just drawn.

Find the centre of your circle. Peel the backing paper off the back of your felt name and position it in the centre of the right side of your fabric circle.

headband holder collage 2

Cover your felt with a press cloth again and run a hot steam-free iron over the felt, to secure it to your fabric.

Now you’re ready to appliqué! For some great tips on appliquéing you can learn the basics from this post. I like to use a blanket stitch for my appliqués. I feel it gives a really neat finish and it protects the raw edges of the felt or fabric. For this project, I’ve used the ‘blanket stitch’ setting on my sewing machine, using a clear plastic appliqué foot.

You can also blanket stitch by hand, or even do a simple running stitch. Truth be told, you don’t even have to stitch the appliqué down because the fusible webbing will keep it in place. But it does give it a lovely finish!

Start stitching in a join or bend on your word. I started on the base of the ‘e’. This helps to disguise your stitching when it joins.

Stitch slowly, carefully and close to the raw edge of the felt. Don’t forget to pivot your fabric (with the sewing machine needle down) when you come to a bend or corner. Be sure to carefully secure your stitching at the end.

When you’re finished, your stitching will look something like this;

M and M 15

Now it’s time to pad up the fabric by adding some iron-on or fusible batting, like Pellon. I like to do this as it helps the fabric sit nicely in the hoop. I do it after the appliquéing step, so that the sewing machine doesn’t have too many layers to contend with.

Cut your Pellon batting in a circle that is just slightly smaller than your fabric. Lay the batting with the fusible dots down and facing the back of your appliquéd piece of fabric. Using a press cloth (as the batting will melt without it), use your hot non-team iron to secure the batting. I had some scraps and actually used two pieces of Pellon. You can see how they meet on the back of the fabric here. I’m all for using scraps and saving cash!

M and M18

Now it’s time to prepare the head band ribbons that will hang from the base of your hoop. Place your 1” wide ribbon over your 1.5” wide ribbon and centre it. Fold both layers over and stitch them together.

Next, using your erasable marker, measure 4 inches from the top of your ribbons and mark a small spot on the edge of your 1” ribbon. Continue down your ribbon, marking spots 4” apart. Fold back the top ribbon and now mark your 1.5” ribbon, except this time you are marking them 3’ apart. You can just see my markings in blue (top right photo, below).

Now, starting at the top of your ribbons (where you stitched them together), line up your markings so that the top ribbon’s spot is directly over the bottom ribbon’s spot. Join both ribbons together by sewing a horizontal line across the width of the 1” ribbon. Be sure to use your reverse stitch on the machine to secure the beginning and end of your stitching.

Continue to line up your markings and stitch them down. You will find that the bottom ribbon will remain flat and the top ribbon will end up with loops in it.

You’ll have nine loops in total. Once you’ve trimmed off your threads, also trim the base of the ribbons. Heat seal the ends so that they don’t fray. I have a machine I use, but a lighter or lit match provides enough heat to do the same job. Just quickly run the flame along the open edge of the ribbon to melt the fibres together. You can see the trimmed loops and heat-sealed ends here. Don’t forget to dampen your erasable marker spots to remove them too!

headband holder collage 3

Well, it’s now time to put everything together! I hope you’re still following along and are able to use the images for some added guidance.

Unscrew your embroidery hoop and lay your fabric over the inside ring. Pop the outside ring over the fabric and tighten the screw just enough to gently hold everything in place. Make sure your name is centred, and that the screw is centred on the top of the hoop.

Take the top of your ribbon (the part you stitched down) and feed it through the top side of the base of the hoop. The top right image below shows you how the tip of the ribbon pokes through on the base of the back.

Tighten your screw as firmly (but gently) as you can. Then gently pull your fabric at the back so that there are no bubbles or puckers on the front of your hoop. You want your fabric sitting taut and smooth.

Flip your hoop over and fold your extra allowance down inside the hoop.

If it’s a tad long, trim away some of the excess (ensuring you still have enough fabric to tuck in) (lower right photo, below.)

headband holder collage 4

Now we’re ready to secure everything, so be sure you’re happy with how everything appears at the front of the hoop and make some adjustments if necessary.

Heat your hot glue gun, and run a line of hot glue along the inside of the wooden rim. Tuck your fabric over and use the glue to secure it down. Only cover a couple of inches at a time, lest your hot glue set before you get to it! When you’ve finished, your hoop should sit flush against a flat surface.

M and M19

There are many other ways to finish the back of an embroidery hoop. You can cover the inside ring with a circle of cardboard, or circle of felt. But for the sake of simplicity, I have left it plain but neat.

We’re just about done. We just need to pretty it up! Tie a bow with some ribbon and trim the ends. Be sure to heat seal the ends too. Glue your bow to the top front of your hoop, and you’re done!

M and M23

Such a simple project! You can feed head bands through the loops and you can also attach clips too. And it’s also a pretty addition to any girl’s bedroom!

M and M22

Because this is the second in the Little Girl’s Bedroom Makeover Series, you won’t want to miss Lauren’s first post in the series, the pillowcase with trims and lace!
You won’t want to miss more fabulous posts here, so please follow SewMcCool by e-mail (the link is at the top of the right-hand column) or join me on BlogLovin’ – the button is just below the e-mail feed box! :)

 

 

Related Posts Plugin for WordPress, Blogger...

Comments

Trackbacks

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

CommentLuv badge